This page provides specific information to consider before you start your Opal-6 design.
Please contact our support team with any questions you have during the design process and use our free design review when you have finished your design.

Starting a Design - using the IOMux tool

The i.MX6 can be confusing to design with as it uses a multiplexer to assign up to 8 different functions to each IO pin.
Freescale provides an IOMux tool (available on the i.MX6 "Software & Tools" tab, under "Software Development Tools -> Initialization/Boot/Device Driver Code Generation") which makes it easy to sort through these options.
For Opal-6 we have two IOMux files that we have generated for the Opal CPU Module and the Opal Development Kit:

Opal-6 SoM IOMux File (in development)
Opal-6 Development Kit IOMux File (in development)

In the case of the CPU Module file, this shows which pins have been used on the module and should be your starting point. All the pins NOT SELECTED are available on the interface for you to use in your design. The Development Kit file is a good reference to see which pins we used for the different functions in the kit.

The IOMux file you generate is also an excellent way to document your design, and is very useful for software developers when setting up Operating System images and device drivers.

Reference Designs

Where possible, we encourage you to use our development kit as a starting point for your design.
The advantages are:

It minimizes software changes
We are familiar with the circuit so can assist with debugging your design
You have less design work to do!

We also encourage you to use the library symbols for the module, and development kit schematics, available from our web site.

Booting

Opal-6 boots from:

On-board eMMC
SD Card (SD2 controller)
USB (for programming eMMC)

Other boot sources are possible, but not tested. Please contact use if you need something other than these options.
Several pins must be configured correctly in order for Opal to boot correctly. The following table includes the pins involved in the boot process and how they should be configured.

Signal	Boot Function	NAND Boot Setting (0=pull down, 1=pull up, X=don't care)	SD Boot
BOOT_MODE0		Main boot setting: 00 Boot from NAND/SD 11 Boot from USB
BOOT_MODE1
BOOT_CONFIG_1	BOOT_CFG1[7]	1	0
BOOT_CONFIG_2	BOOT_CFG1[6]	0	1
BOOT_CONFIG_3
BOOT_CONFIG_4		0	0 (SD boot)

Connectors

Opal-6 uses 2 x 168-way Hirose FX10A-168S-SV.
The corresponding mating connector is: FX10A-168P-SV1(71).

Debug and Programming Connections

Even if you design does not need the following, we recommend you provide a way of accessing these connections in order to successfully debug during development and program during production.

Boot Switches	If your design boots from NAND flash, you should include at least the switch to enable USB boot for programming. Including switches to also allow SD boot will provide more options for programming during manufacture.
Serial Port	One serial port should be accessible for debug. UART4 is used on our development kit so should be your first choice.
USB OTG Port	This port should be available in USB function mode if your design boots from NAND flash. This is required to program the flash.
Ethernet	Ethernet is useful for download and debug, and required for Windows Embedded Compact designs.

Layout Recommendations

The development kit schematics include layout recommendations and these should be added to your own design.

When creating a PCB footprint, ensure:

The location post holes are the correct size - one hole is 1.0 mm and the other is 0.9 mm in diameter.
The location post holes are non-plated
The distance between the connectors is exactly as specified.

Failure to do the above may result in the connectors not being located correctly relative to each other. This will cause stress on the connector and solder joints will break or become unreliable.

Critical Signal Summary

On this page

Opal-6 Design Guide